Pooler HVAC Company handles the full range of heating and cooling work for homeowners, landlords, property managers, and businesses across Pooler and Chatham County. Whether you need an urgent repair, a full system replacement, or a seasonal tune-up before the heat settles in, we are the call to make.
Reach us at (912) 742-8959. We are available every day from 8:30 AM to 10:00 PM.
We answer when you call. We explain the work. We leave it running right.
If you're not sure your system can keep up, the first step is a proper diagnosis. An AC that blows warm air, a heat pump that runs but does not cool, a heater that will not turn on, or a system that short-cycles and shuts off early all point to something specific. We go through the equipment before we quote parts, so you know what is actually wrong and what fixing it involves.
We handle residential repair calls and commercial service calls across Pooler and the surrounding area. A clogged evaporator coil behaves differently from a refrigerant issue, and a failed capacitor is a different repair from a bad control board. The diagnostic step matters, and we do not skip it.
We treat your home and its system the way we would our own. That means checking the full picture on a service call, not just the first thing that looks off.
Reach out and we will talk through the symptoms.
This area runs every kind of furnace, AC, and heat pump, and what drives the cost of a replacement is not a mystery once you walk through it. System type, the size of the space being conditioned, and the equipment selected all factor into the final number. A mini-split for a converted garage costs differently from a full central air replacement in a two-story home, and a commercial rooftop unit is a different project again.
We handle central air installation, heat pump installation, mini-split and ductless system installation, and full system upgrades for both residential and commercial properties. Every installation job gets a load calculation before equipment is selected. A system sized for the space performs better and costs less to run than one sized for whatever came before it.
We tell you if a permit is needed. We size the system to the home. We explain the options.
On installation work, you get a written scope before anything starts. That covers what is being installed, what the visit involves, and what the price is based on. Call for a quote and we will walk through it with you.
Chatham County sits in coastal Georgia, where the cooling season runs long, humidity is a constant, and a mild winter means the heating load is light compared to most of the country. The work that comes up most here reflects that. Whole-home dehumidification, heat pump installation, and high-efficiency AC replacement are not niche services in this area. They are the jobs that match what the climate actually demands.
Coastal Georgia humidity does not stop when the AC is running. If the air in your home feels clammy, you are seeing condensation on windows or interior surfaces, or there is a persistent musty odor that cleaning does not fix, the problem is often moisture that the central AC alone is not pulling out. A whole-home dehumidifier integrates directly with the existing system and holds the indoor relative humidity at a target level, independent of the cooling cycle.
When you call us, the job gets scoped on the phone, not guessed at. We will ask about the symptoms, the square footage, and how the current system is set up before anything is scheduled.
Heat pumps are well-matched to Pooler's climate because they handle both heating and cooling in a single unit. With mild winters and a long cooling season, a heat pump runs efficiently in both directions without the fuel costs of a gas system. We install standard split systems and mini-split configurations, and the right choice depends on the layout of the space, whether ductwork is in place, and what the load calculation shows.
Equipment sized for the space rather than for the last unit is how a heat pump delivers what it is rated for. We go through that process on every installation.
An aging central AC system shows its age in a few ways: rising energy bills, rooms that never quite reach the set temperature, or a unit that runs constantly without keeping up. A replacement is not just swapping one box for another. Load calculation, equipment selection, and proper system sizing all affect how the new unit performs through a Georgia summer.
Efficiency ratings translate directly into operating costs when the system runs for eight or nine months a year. A higher SEER2-rated unit costs more upfront and less every month. We will walk you through the numbers so the decision makes sense before you commit.
Give us a call and we will take care of it.
Leaky ductwork is one of the most common reasons a home with a well-functioning AC still has uneven temperatures and high energy bills. Conditioned air escaping into an attic or crawl space before it reaches the living area forces the system to work harder and longer. We handle duct sealing and duct leak repair for both residential and commercial systems.
Thermostat and smart thermostat installation is straightforward work that can make a noticeable difference in how consistently the system holds temperature. Programmable controls and zoning setups let different areas of the home or building run on different schedules, which matters in a space that does not cool or heat evenly.
Indoor air quality covers whole-home air filtration, air purifier installation, and airflow troubleshooting. If certain rooms feel stuffy or air quality is a concern, those are problems with diagnosable causes. We work through the airflow picture before recommending equipment.
Doing HVAC work right matters, and we'll help you get it right, starting with a proper maintenance visit before the system is under load. A tune-up covers refrigerant level checks, coil cleaning, air handler and blower inspection, control testing, and a look at the components most likely to cause a mid-season failure. Catching a worn contactor or a dirty evaporator coil in April costs far less than an emergency call in August.
We schedule residential maintenance and commercial HVAC maintenance. Booking before the peak cooling season means shorter wait times and a system that has been checked before it is running daily. Property managers with multiple units benefit from getting all of them on a consistent maintenance schedule.
A written scope on installation work applies to maintenance agreements too, so you know what the visit covers before it is scheduled.
We're ready to get your heating and cooling running again.
The sooner you call, the sooner your comfort is back. A system that goes down in July with temperatures in the upper nineties is not a situation to wait out. No cooling, no heat when temperatures drop overnight, or a system that shuts off and will not restart all qualify as emergency calls. We take them.
Emergency service is available every day from 8:30 AM to 10:00 PM. That covers homeowners dealing with a failed AC and property managers with a tenant in a rental unit who has no cooling. Call the moment the problem shows up. We will ask the right questions on the call and get the visit scheduled.
We tell you if a permit is needed. We size the system to the home. We explain the options.
Call and we'll handle the furnace, the AC, and the ductwork.
We work across both residential and commercial accounts. On the residential side, that means home HVAC repair, system replacement, and seasonal maintenance for single-family homes and townhomes throughout the area. On the commercial side, it covers commercial AC repair, commercial heating repair, and service for rental properties, apartment units, and small commercial buildings.
Landlord and property manager calls are welcome. A rental unit with a failed AC is a tenant issue and a liability issue at the same time, and getting it handled quickly matters. We treat commercial calls the same way we treat residential ones: diagnosis first, then a clear explanation of what the repair or replacement involves.
We serve Pooler and the broader Chatham County region, including Savannah, Garden City, Port Wentworth, Bloomingdale, Rincon, Guyton, Thunderbolt, and Tybee Island. If you are in the greater Savannah metro and need heating or cooling work, call and we will confirm coverage for your address.
A system that has stopped cooling entirely during a Pooler summer, a heat pump that will not run in either direction, or a heating system that goes out during one of the area's cold nights all qualify as emergency calls. Any situation where the home or building is becoming genuinely uncomfortable or unsafe because the HVAC system is down is worth calling about immediately. We take emergency calls every day from 8:30 AM to 10:00 PM and scope the situation on the phone.
The most common warning signs are a system that runs constantly without reaching the set temperature, one that short-cycles and shuts off after a few minutes, rising energy bills without a change in usage, and uneven cooling between rooms. Ice forming on the evaporator coil or refrigerant lines is another indicator that something is wrong with the system's airflow or charge. Any of those symptoms is worth a call before the system stops working entirely.
The age of the system and the cost of the repair relative to a replacement are the two main factors. A system that is more than 12 to 15 years old, has needed multiple repairs in recent seasons, and now faces a major component failure is often a better candidate for replacement than another repair. We go through that calculation on the service call and give you a straight answer about whether the repair is worth doing on the equipment in front of us.
Uneven temperatures usually point to a ductwork issue, an airflow imbalance, or a system that was not sized correctly for the layout of the home. A room at the end of a long duct run may not be getting adequate airflow, or a duct may be leaking conditioned air into an unconditioned space before it reaches the register. We check the distribution side of the system, not just the equipment, when uneven temperatures are part of the complaint.
Banging or clanking often points to a loose or broken component inside the air handler or compressor. Squealing can indicate a worn blower motor bearing or a belt issue on older equipment. Rattling at startup or shutdown is sometimes a loose panel, but it can also indicate a refrigerant issue causing liquid slugging in the compressor. Any new noise that was not there before is worth a call, because most of them indicate something that will get worse if left alone.
The system is run through a full operating cycle after any repair or installation work. For a repair, that means checking the pressures, confirming the system reaches setpoint, and verifying that the fault that caused the call is resolved. For a new installation, it includes thermostat calibration, airflow verification at the registers, and a check of the controls. We do not close out a visit on a system that has not been confirmed running correctly.
A straightforward repair, such as a capacitor replacement or a thermostat swap, usually takes one to two hours. A more involved repair involving refrigerant recovery and recharge, coil cleaning, or a control board replacement takes longer. A full system installation is typically a full day's work depending on the configuration. We give you a realistic time estimate on the call based on what the job involves.
It depends on the job and the access involved. For most interior work, someone needs to be present or access needs to be arranged in advance. For outdoor unit work only, access requirements are different. Let us know your situation when you call and we will confirm what is needed for your specific job before the visit is scheduled.
Yes. HVAC work involves electrical components, refrigerant handling, and equipment that is running during testing. Keeping children and pets clear of the work area, both indoors near the air handler and outdoors near the condenser, makes the visit safer and lets the work move faster. We will let you know at the start of the visit which areas to keep clear.
Chatham County's coastal humidity means a standard AC system often cannot pull enough moisture out of the air to make the home feel comfortable, even when the temperature is at setpoint. A whole-home dehumidifier integrates with the existing HVAC system and holds indoor humidity at a target level independently of the cooling cycle. The result is better comfort at higher thermostat settings and less strain on the cooling equipment through the long Georgia summer.
Heat pumps handle both heating and cooling from a single unit, which is well-matched to a climate with mild winters and a long cooling season. Because hard freezes are infrequent in the Pooler area, a heat pump runs efficiently in heating mode without relying heavily on supplemental heat strips. One system covers both seasons, which simplifies maintenance and reduces the number of separate pieces of equipment to service.
It starts with a load calculation based on the home's actual square footage, insulation, and orientation rather than repeating the size of the unit being replaced. Equipment is selected to match the load, and the efficiency rating is discussed in terms of what it means for monthly operating costs through a Georgia cooling season. The installation includes checking the duct system for leaks that would undermine the new unit's performance before anything is commissioned.
Pooler HVAC Company covers the full range of heating and cooling work: AC repair, heating repair, heat pump service, system installation and replacement, ductwork sealing, indoor air quality, and seasonal maintenance. Whatever the system, whatever the problem, we handle it.
We are available every day from 8:30 AM to 10:00 PM.
Call (912) 742-8959 for a quote.
We answer when you call. We explain the work. We leave it running right.
Reach out and we will talk through what the job involves.
Below is a quick look at the heating and cooling work we handle across Pooler and Chatham County. Each service is listed with what the visit covers, who it fits best, and a practical note to help you decide what to schedule first.
Call us at (912) 742-8959 any day from 8:30 AM to 10:00 PM and we will walk through the details for your specific system.
| Service Type | What It Covers | Best For | What to Keep in Mind |
|---|---|---|---|
| Whole-Home Dehumidification & Humidity Control |
| Pooler and Chatham County homes where the AC runs but the air still feels clammy or musty | Coastal Georgia humidity often exceeds what a standard central AC can remove on its own, especially during the long cooling season |
| Emergency HVAC Service |
| Any situation where the home or a rental unit is without heating or cooling and cannot wait | We take emergency calls every day from 8:30 AM to 10:00 PM and scope the situation on the phone before the visit is scheduled |
| Heat Pump Installation |
| Homeowners who want a single system that handles both heating and cooling efficiently through Pooler's mild winters and long summers | With infrequent hard freezes in this area, a heat pump runs efficiently in heating mode without heavy reliance on backup heat strips |
| AC Repair & Service |
| Homeowners and property managers with a cooling system that is underperforming or not running | Diagnosing the cause before quoting parts avoids replacing components that are not the actual problem |
| High-Efficiency Central AC Replacement |
| Homeowners with an aging AC that is running constantly, losing efficiency, or facing a major repair | A higher SEER2-rated unit costs more upfront and less every month, which matters when the system runs eight or nine months a year in coastal Georgia |
| Indoor Air Quality & Air Filtration |
| Households where air quality, allergens, or stuffiness in certain rooms is a concern | Stuffy rooms and persistent odors often have diagnosable causes on the distribution side of the system |
| Ductwork Repair & Sealing |
| Homes with uneven temperatures, high energy bills, or a system that runs longer than expected | Conditioned air escaping into an attic before it reaches the living area forces the system to run harder and longer |
| Heating Repair & Service |
| Any home or building where heat is not reaching setpoint or the system will not start | Coastal Georgia winters are mild but a failed heater on a cold night still needs prompt attention |
| Thermostat & Smart-Control Installation |
| Anyone looking to improve temperature consistency or reduce energy use with programmable controls | A smart thermostat can make a noticeable difference in how evenly the system holds temperature through the day |
| Seasonal Maintenance & Tune-Ups |
| Homeowners and property managers who want the system checked before peak season demand | Scheduling before the summer cooling season means shorter wait times and a system that has been verified before it runs daily |
| Full System Installation & Replacement |
| Homeowners replacing an aging system or upgrading to a higher-efficiency unit | A load calculation ensures the replacement unit is sized for the actual space, not just matched to what came before |
| Heat Pump Repair & Service |
| Homes with a heat pump that is struggling in either heating or cooling mode | A heat pump that works in one direction but not the other often points to a reversing valve or refrigerant issue |
How often should an HVAC system in Pooler be serviced?
For most homes in Chatham County, once a year before the cooling season is the minimum. Because the cooling season here runs from roughly April through October, a spring tune-up gives the system a chance to be inspected, cleaned, and verified before it carries its heaviest load. A heat pump that runs in both directions benefits from a check before both the heating and cooling seasons. We schedule residential and commercial maintenance calls and can confirm what interval makes sense for the equipment you have.
What causes a system to short-cycle and shut off after only a few minutes?
Short-cycling usually points to one of a few causes: an oversized system that cools the space too quickly and shuts off before completing a full cycle, a refrigerant issue that causes the system to trip a pressure limit, a dirty evaporator coil restricting airflow, or a failing capacitor that cannot sustain the compressor through a full run. The pattern matters when we diagnose it. A system that short-cycles consistently is worth a call before the underlying cause causes a harder failure.
How do ductwork leaks affect energy bills and comfort?
Leaky ducts let conditioned air escape into unconditioned spaces like attics and crawl spaces before it reaches the living area. The system has to run longer to compensate, which raises energy use and wear on the equipment. It also means some rooms may never reach the set temperature no matter how long the system runs. We inspect the duct system for leaks and seal them at the joints and connections where losses are most common. In a home that has never had the ducts checked, this work often makes a noticeable difference in both comfort and operating costs.
System Checked Before Parts Are Quoted
We go through the equipment and run a full diagnostic before recommending any parts. You know what is actually wrong before any repair cost is confirmed.
How do estimates and pricing work for HVAC repairs and installations?
We scope the job on the phone first. You tell us the symptoms, the equipment, and the situation, and we give you a clear picture of what the visit involves and what the price is based on before anything is scheduled. For installation work, you get a written scope that covers what is being installed and what the price reflects. The exact figure is confirmed once the job is fully scoped, not estimated broadly and adjusted later.
Call us at (912) 742-8959 and we will walk through it.
When is it worth attempting a DIY fix versus calling a technician?
Replacing a filter, clearing debris from around the outdoor condenser, and checking that the thermostat is set correctly are all reasonable first steps a homeowner can take before calling. Beyond that, HVAC work involves refrigerant handling, electrical components, and equipment that needs to be run through a full cycle under load to verify the repair. A fix that looks straightforward from the outside often depends on reading the system's pressures and controls during operation. If the basic checks do not resolve the issue, a call is the right next step.
What signs point to a refrigerant or airflow problem?
Refrigerant issues often show up as an AC that runs continuously without cooling the space, ice forming on the evaporator coil or the refrigerant lines, or a system that blows air that is not as cold as it should be. Airflow problems tend to produce uneven temperatures, weak output at the registers, or a system that overheats and shuts off on a high-pressure limit. Both can mimic each other in how they present, which is why we check pressures and airflow together rather than assuming one or the other.
Diagnosis Explained on Every Call
When you call, we ask the right questions to scope the job on the phone. You get a clear picture of what the visit involves before anything is scheduled.
What does a seasonal tune-up actually cover?
A tune-up is not just a filter swap. We check refrigerant levels, clean the evaporator and condenser coils, inspect the blower motor and air handler, test the controls and safety limits, and look at the components most likely to cause a mid-season failure. A worn contactor, a weak capacitor, or a dirty coil that is caught in a maintenance visit costs far less to address than an emergency call in the middle of a Georgia summer. We also note anything that is trending toward a problem so you can plan ahead rather than react.
How does indoor humidity affect comfort and the HVAC system in coastal Georgia?
High indoor humidity makes the air feel warmer than the thermostat reads, which leads many homeowners to lower the setpoint and run the system harder. It also creates conditions where condensation forms on surfaces and musty odors develop. A standard central AC removes some moisture as a byproduct of cooling, but in Chatham County's climate it often cannot keep up with the humidity load on its own. A whole-home dehumidifier integrated with the existing system holds indoor relative humidity at a target level independently of the cooling cycle, which improves comfort and reduces the load on the AC.
Emergency No-Heat and No-Cool Calls Handled
A system that goes down in the middle of a Pooler summer or on a cold night does not have to wait. We take emergency calls every day from 8:30 AM to 10:00 PM.
What is the difference between repairing an older system and replacing it?
The age of the equipment and the cost of the repair relative to a replacement are the two main factors we look at. A system that is more than 12 to 15 years old, has needed multiple repairs in recent seasons, and now faces a compressor or coil failure is often a better candidate for replacement. A younger system with a single failed component is usually worth repairing. We go through that calculation on the service call and give you a straight answer about the equipment in front of us, including what the repair involves and what a replacement would look like in comparison.
How does a dirty filter or coil hurt system performance?
A clogged filter restricts airflow into the system, which reduces how much conditioned air reaches the living space and forces the blower to work harder. Over time, restricted airflow causes the evaporator coil to ice over, which shuts down cooling entirely. A dirty evaporator or condenser coil reduces the system's ability to transfer heat, which lowers efficiency and raises operating costs. Coil cleaning is part of every maintenance visit we do because a clean coil is one of the simplest ways to keep the system performing at its rated capacity.
How long does a full HVAC system replacement take?
A standard central AC or heat pump replacement is typically a full day's work. A mini-split installation for a single zone is usually shorter. A more complex job involving multiple zones, new ductwork, or a commercial rooftop unit takes longer. We give you a realistic time estimate on the call based on what the job actually involves, so you can plan the day accordingly. The system is run through a full commissioning cycle before we close out the visit.
Call us at (912) 742-8959 any day from 8:30 AM to 10:00 PM and we will talk through what the job involves, give you a clear price, and get it on the schedule.
(912) 742-8959